Our prices are exclusive of taxes and shipping. 18% GST shall be added during check out. Happy Shopping! :)  

Robocraze Welcome to Robocraze

Radio Frequency: Transmitter with Encoder and Receiver with Decoder

Transmit and receive data wirelessly without the hassle of connecting them to Arduino or a microcontroller, and even without programming!

Radio Frequency: Transmitter with Encoder and Receiver with Decoder

What is RF module?
RF (radio frequency) module is a small electronic device, to transmit and receive data wirelessly using radio signals. In an embedded system, we often need to communicate between two devices wirelessly. We use RF communication only because it doesn’t require a line of sight. Several carrier frequencies are commonly used in commercially available RF modules such as 433MHz, 915MHz and 2400MHz. Here we’ll see about RF 433MHz transmitter and receiver.

RF 433 MHz transmitter and receiver with encoder and decoder:
RF 433MHz transmitter and receiver modules are embedded with HT12e and HT12d respectively. 

RF 433 MHz Transmitter:
An RF transmitter module is a small PCB sub-assembly capable of transmitting a radio wave and modulating that wave to carry data. Transmitter modules are usually implemented alongside a microcontroller which will provide data to the module which can be transmitted. RF transmitters are usually subject to regulatory requirements which dictate the maximum allowable transmitter power output, harmonics, and band edge requirements.

RF Transmitter with Encoder

RF 433 MHz Receiver:
An RF receiver module receives the modulated RF signal, and demodulates it. There are two types of RF receiver modules: superheterodyne receivers and super-regenerative receivers. Super-regenerative modules are usually low cost and low power designs using a series of amplifiers to extract modulated data from a carrier wave. Super-regenerative modules are generally imprecise as their frequency of operation varies considerably with temperature and power supply voltage. Superheterodyne receivers have a performance advantage over super-regenerative; they offer increased accuracy and stability over a large voltage and temperature range. This stability comes from a fixed crystal design which in the past tended to mean a comparatively more expensive product. However, advances in receiver chip design now mean that currently there is little price difference between superheterodyne and super-regenerative receiver modules.

RF Receiver with Decoder

HT12e:
HT12E is a 2^12 series encoder IC, widely used in remote control and very common among Radio Frequency RF applications. This HT12E IC is capable of convertin12-bit Parallel data inputs into serial outputs. These bits are classified into 8 (A0-A7) address bits and 4(AD0-AD3) data bits. Using the address pins we can provide 8-bit security code for secured data transmission between the encoder and the decoder. The encoder and decoder should use the same address and data format. HT12E is capable of operating in a wide Voltage range from 2.4V to 12V and also consists of a built in oscillator.


HT12d:
HT12D is a 2^12 series decoder IC for remote control applications, manufactured by Holtek. It is commonly used for radio frequency (RF) wireless applications. By
using the paired HT12E encoder and HT12D decoder we can transmit 12 bits of parallel data serially. HT12D simply converts serial data to its input (may be received through RF receiver) to 12-bit parallel data. These 12 bit parallel data is divided into 8 address bits and 4 data bits. Using 8 address bits we can provide 8-bit security code for 4-bit data and can be used to address multiple receivers by using the same transmitter.

Connections:
RF transmitter with HT12e:
RF transmitter module is embedded with HT12e IC
• VDD and VSS: Positive and negative power supply pins.
• OSC1 and OSC2: Input and output pins of the internal oscillator present inside the IC.
• TE: This pin is used for enabling the transmission, a low signal in this pin will enable the transmission of data bits.
• A0 – A7: These are the input address pins used for secured transmission of this data. These pins can be connected to VSS for low signal or left open for high state.
• AD0 – AD3: These pins are feeding data into the IC. These pins may be connected to VSS for sending LOW since it is an active low pin
• DOUT: The output of the encoder can be obtained through this pin and can be connected to the RF transmitter.

 RF transmitter with HT12e

RF receiver with HT12d:
• VDD and VSS are used to provide power to the IC, Positive and Negative of the power supply respectively. Its operating voltage can be in the range 2.4V to 12V
• OSC1 and OSC2 are used to connect external resistor for the internal oscillator of HT12D. OSC1 is the oscillator input pin and OSC2 is the oscillator output pin.
• A0 – A7 are the address input pins. Status of these pins should match with status of address pin in HT12E (used in transmitter) to receive the data. These pins can be connected to VSS or left open.
• DIN is the serial data input pin and can be connected to an RF receiver output.
• D8 – D11 are the data output pins. Status of these pins can be VSS or VDD depending upon the received serial data through pin DIN.
• VT stands for Valid Transmission. This output pin will be HIGH when valid data is available at D8 – D11 data output pins.

RF receiver with HT12d

Experiment:

Working:
The aim of this project is to implement a wireless transmitter and receiver using RF modules. It uses radio signals to transmit the data. The working of the project is as follows:
The transmitter and receiver sections are placed at a distance. In order to show the working of wireless communication between transmitter and receiver, 4 LEDs at receiver side are controlled by 4 buttons at transmitter section (all these LEDs and buttons are inbuilt on the modules).
The HT12E encoder IC converts the 4-bit data from the 4 data pins that are connected to buttons into serial data. This serial data is sent to RF transmitter. The RF transmitter transmits this serial data using radio signals.
At the receiver side, the RF receiver receives the serial data. This serial data is sent to HT12D decoder IC which converts into 4 bit parallel data. The 4 data pins of the decoder are connected to LEDs. According to the buttons pushed, the LEDs can be turned ON or OFF.

Applications:
• As RF Modules doesn’t require a line of sight communication, the transmitter and receiver can be isolated over a distance and data can be transmitted successfully.
• The wireless transmitter and receiver can be used in car door and garage door controllers.
• They can also be used in home automation systems.

 

 

Write Your Comment

Only registered users can write comments. Please, log in or register