NFC BASED SECURITY DOOR LOCK

NFC BASED SECURITY DOOR LOCK - Robocraze

Let us take a closer look at the hardware components used for this project:

1.  Witty Fox NFC board

2.  Witty Fox Storm board

3.  12V Solenoid lock

4.  5V relay module

5.  Jumper Wires

6. 5V microUSB Power adapter

7.  12V Power adapter

 

The block diagram for the hardware connections is shown below:

 

Connection Diagram

 

 

To have a better understanding of how to make the hardware connections, please refer to the video below:

 

 

 

 

The code for this project is given below. Before uploading this code, make sure you have installed the  RF430 library.



#include <Wire.h> 
#include <RF430CL.h> //include to use the Witty Fox NFC board
#include <NDEF.h>
#include <NDEF_TXT.h>

#define RF430CL330H_BOOSTERPACK_RESET_PIN 25 //reset pin of NFC board connected to GPIO
#define RF430CL330H_BOOSTERPACK_IRQ_PIN 26 //interrupt pin of NFC board connected to GPIO

RF430 nfc(RF430CL330H_BOOSTERPACK_RESET_PIN, RF430CL330H_BOOSTERPACK_IRQ_PIN);
NDEF_TXT msg;
uint8_t buf[512];
String password = "Robocraze"; //declaration of the password which will unlock the door
void DumpSRAM();

void setup()
{
  Serial.begin(115200);
  delay(1000);
  pinMode(2, OUTPUT); //pin connected to on-board LED
  pinMode(13, OUTPUT); //pin connected to input of Relay

  Serial.println("Initializing I2C-");
  Wire.begin();

  Serial.println("Initializing NFC Tag-");
  nfc.begin();

  Serial.println("Activating NFC transceiver-");
  nfc.enable();

Serial.println("Now waiting for NFC master to post a Text block.");

  msg.setPayloadBuffer(buf, 512); // Set allocation buffer used to store incoming NDEF data
}

void loop()
{
  digitalWrite(13, HIGH);

  if (nfc.loop())
{
// If nfc.loop() returns true, nfc.disable() is implicitly run...
    if (nfc.isError())
{
  Serial.println("NFC transceiver reports its SRAM contents do not contain valid NDEF data.");
      DumpSRAM();
}
    if (nfc.wasRead())
{
      Serial.println("NDEF tag was read!");
}
    if (nfc.available())
{
      Serial.print("NFC master has written a new tag! ");
      uint16_t len = nfc.getDataLength();
      Serial.print(len);
      Serial.println(" bytes");

      Serial.println("Assuming data is NDEF TEXT; importing-");
      int ret = msg.import(nfc);
  if (ret < 0)
{
        Serial.println("ERROR importing NDEF TEXT data. SRAM dump:");
        DumpSRAM();
}
      else
{
        Serial.println("Success!");
        Serial.print("Language code: ");
        Serial.println(msg.getLanguage());
        Serial.println("Text block:");
String Data = msg.getText();
        Serial.println(Data);

        if (Data == password) //door will only unlock if the received message matches with the password set in the beginning
{
          int i;
          for (i = 0; i < 5; i++)
{
            digitalWrite(13, LOW); //door will unlock for approximately 5 seconds
//blink onboard LED when the door is unlocked
            digitalWrite(2, HIGH);
            delay(500);
            digitalWrite(2, LOW);
            delay(500);
}
i = 0;
}
}
      nfc.flush();
}
    nfc.enable();
}
}

void DumpSRAM()
{
  uint8_t sram[128];

  nfc.readSRAM(0x0000, sram, 128);
  for (int i = 0; i < 128; i++)
{
    if (sram[i] < 0x10)
      Serial.print('0');
    Serial.print(sram[i], HEX);
    Serial.print(' ');
    if (i % 9 == 8)
      Serial.println();
}
  Serial.println();
}

Working:

Once the program is uploaded and the setup is completed, install the TagWriter Application made by NXP - Available on  Android and  iOS.

IMG_256
Open the app, go to the “Write tags” option, and click on "New Dataset" followed by "Plain Text". Enter the password which you have set in the code and click on the "Save & Write" option at the bottom. 
1.

IMG_256

2.

IMG_256

3.

IMG_256

A screen will pop up displaying the data which you have entered, you may or may not choose the "Confirm Overwrite" option. Press on write again and take your phone close to the NFC reader.

IMG_256

The phone should be able to write to the NFC reader when they are within 5cm of each other. It will take 1-2 seconds for the write operation to be completed which will be indicated by an alert tone made by the application. The door will open as soon as you pull out your phone away from the readers' proximity. 

IMG_256

Once you create a dataset, you can access it directly in the app under "My Datasets" tab, this means you don't have to enter the password in the application every single time.

Feel free to come up with other cool ideas and do share them with us. You can buy the Witty Fox boards at  Robocraze .
Comment below if you get stuck or have any further questions.

 

Frequently Asked Questions

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.

Components and Supplies

You may also like to read